01
сен
Installation of my brand-new 20 year old woodstove. This stove was manufactured by Federal Airtight and sold under the Consolidated DutchWest brand but distributed by Vermont Castings in the early. Dutchwest Federal Airtight Manual Wood Stove. Stove Federal Airtight Wood. Federal Airtight Wood Burning Stove Discoverstuff. Stove Federal Airtight Wood.
There are quite a few variations of the Dutchwest out there and yours looks like it is one of the earliest models of the Dutchwest. Some of the earlier models left a lot to be desired in the way of the cat housing and the cat performance. Can you access the cat by removing the square plate on the to pof the stove that sits over top of the cat? Blok pitaniya shim 3528 peredelka creek. If so it is probably one of the earliest models. At a minimum I would suggest. 1)Going over all the seams on the stove to check for leaks as most of the stoves that age are due for a rebuild/reseal.
2) Checking all the door gaskets paying very careful attention to the ash pan door gasket and the two front door gaskets. If those gaskets aren't right you will have a lot of problems with the performance 3) Carefully check the inside firebox for any warping around the cat housing and check the stove back for any warping inside the firebox. If every thing checks out verify the Catalyst is working and if not you can order one from Condar. I think I have the manual for your stove. If you can let me know what the actual model number is or check to see if the square piece on top of the stove, over the cat is removable I can try to PM it to you. It looks to be missing a few parts but it should clean up pretty well. It is the smaller 224 and I can tell if it has a catalyst air feed or not.
This will identify the year it was built I would take the stove apart and re cement because moving these older stoves will cause the cement to pop. It is an easy job and should only take a few hours.
You need to make sure the back and right inner heat shields are in place as well as the perforated cast catalyst damper are intact. Vyazanij kot opisanie. It will probably need a new cat and I would get one from woodstock, but you can get a cheap one from here.
I would also re gasket and you can find the sizes of the gasket here I would also recommend you block off the bottom air ports and install a fan which can be found here. If you put another $150 and some time into it you will have a nice little heater.
Popular Posts
Installation of my brand-new 20 year old woodstove. This stove was manufactured by Federal Airtight and sold under the Consolidated DutchWest brand but distributed by Vermont Castings in the early. Dutchwest Federal Airtight Manual Wood Stove. Stove Federal Airtight Wood. Federal Airtight Wood Burning Stove Discoverstuff. Stove Federal Airtight Wood.
There are quite a few variations of the Dutchwest out there and yours looks like it is one of the earliest models of the Dutchwest. Some of the earlier models left a lot to be desired in the way of the cat housing and the cat performance. Can you access the cat by removing the square plate on the to pof the stove that sits over top of the cat? Blok pitaniya shim 3528 peredelka creek. If so it is probably one of the earliest models. At a minimum I would suggest. 1)Going over all the seams on the stove to check for leaks as most of the stoves that age are due for a rebuild/reseal.
2) Checking all the door gaskets paying very careful attention to the ash pan door gasket and the two front door gaskets. If those gaskets aren\'t right you will have a lot of problems with the performance 3) Carefully check the inside firebox for any warping around the cat housing and check the stove back for any warping inside the firebox. If every thing checks out verify the Catalyst is working and if not you can order one from Condar. I think I have the manual for your stove. If you can let me know what the actual model number is or check to see if the square piece on top of the stove, over the cat is removable I can try to PM it to you. It looks to be missing a few parts but it should clean up pretty well. It is the smaller 224 and I can tell if it has a catalyst air feed or not.
This will identify the year it was built I would take the stove apart and re cement because moving these older stoves will cause the cement to pop. It is an easy job and should only take a few hours.
You need to make sure the back and right inner heat shields are in place as well as the perforated cast catalyst damper are intact. Vyazanij kot opisanie. It will probably need a new cat and I would get one from woodstock, but you can get a cheap one from here.
I would also re gasket and you can find the sizes of the gasket here I would also recommend you block off the bottom air ports and install a fan which can be found here. If you put another $150 and some time into it you will have a nice little heater.
...'>Dutchwest Federal Airtight Manual(01.09.2018)Installation of my brand-new 20 year old woodstove. This stove was manufactured by Federal Airtight and sold under the Consolidated DutchWest brand but distributed by Vermont Castings in the early. Dutchwest Federal Airtight Manual Wood Stove. Stove Federal Airtight Wood. Federal Airtight Wood Burning Stove Discoverstuff. Stove Federal Airtight Wood.
There are quite a few variations of the Dutchwest out there and yours looks like it is one of the earliest models of the Dutchwest. Some of the earlier models left a lot to be desired in the way of the cat housing and the cat performance. Can you access the cat by removing the square plate on the to pof the stove that sits over top of the cat? Blok pitaniya shim 3528 peredelka creek. If so it is probably one of the earliest models. At a minimum I would suggest. 1)Going over all the seams on the stove to check for leaks as most of the stoves that age are due for a rebuild/reseal.
2) Checking all the door gaskets paying very careful attention to the ash pan door gasket and the two front door gaskets. If those gaskets aren\'t right you will have a lot of problems with the performance 3) Carefully check the inside firebox for any warping around the cat housing and check the stove back for any warping inside the firebox. If every thing checks out verify the Catalyst is working and if not you can order one from Condar. I think I have the manual for your stove. If you can let me know what the actual model number is or check to see if the square piece on top of the stove, over the cat is removable I can try to PM it to you. It looks to be missing a few parts but it should clean up pretty well. It is the smaller 224 and I can tell if it has a catalyst air feed or not.
This will identify the year it was built I would take the stove apart and re cement because moving these older stoves will cause the cement to pop. It is an easy job and should only take a few hours.
You need to make sure the back and right inner heat shields are in place as well as the perforated cast catalyst damper are intact. Vyazanij kot opisanie. It will probably need a new cat and I would get one from woodstock, but you can get a cheap one from here.
I would also re gasket and you can find the sizes of the gasket here I would also recommend you block off the bottom air ports and install a fan which can be found here. If you put another $150 and some time into it you will have a nice little heater.
...'>Dutchwest Federal Airtight Manual(01.09.2018)